American Dynamics AD1686B Instruções de Operação

Model AD2150Video MatrixSwitcher/Controller SystemInstallation and Operation InstructionsThis manual describes the installation and operating procedur

INSTALLATIONThis installation should be made by qualified service personneland should conform to all local codes. Safeguards must betaken to avoid un

MONITORS12345RS232 PORTS123KEYBOARDS2345CAMERAS120V60HzCODEBWS BWS BWS BWS2468101214161820222426283032135791113151719212325272931ALARMSRELAYSINONCC1

RS-232 Ports ConnectionsThree RS-232 ports are provided on the rear panel of theAD2150 for control connections (Figure 1-1, page 1-3). RS-232 keyboar

AD Manchester Control Code ConnectionsAD Manchester Control Code output for AD1640/1680 seriesReceivers, Code Distributors, Code Followers/Responders,

POWERING UPThe AD2150 system may be powered on after:• A video input has been connected to Camera 1 input.• A monitor has been connected to Monitor 1

Keyboard ControlThis section of the manual describes the standard AD2150 systemoperating capabilities that are provided from any American Dynamicskeyb

2-2KEYBOARD CONTROL

KeyboardsThe AD2150 may be used with different American Dynamicskeyboards. A list of the AD keyboards that can be used withthe AD2150 is shown in the

Controlling Camera Site FunctionsCamera site control functions (pan/tilt, lens, presets, andauxiliaries) are available after the operator has called t

Running a TourA Tour sequentially displays a selected series of camera videoinputs on a monitor. Monitor Tours are temporary toursdefined by non-menu

This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not tobe copied or disclosed in any manner

Non-Menu ProgrammingThis section of the manual describes the AD2150 system non-menu setupprogramming capabilities. As a security feature, the keyboar

NON-MENU PROGRAMMINGIn most instances, the following non-menu setup descriptionsand commands are the same for all keyboards. Refer to theappropriate

Setting the Day of the WeekThe day of the week must be set prior to programming theEvent Timers, page 4-9. When a code is entered, the three-digit da

Monitor Tour ProgrammingA Tour (Sequence) sequentially displays a selected series ofcamera video inputs on any monitor. Each camera is displayedfor a

Preset (Pre-position) Scene ProgrammingMotorized pan/tilt and lens units with servo control capabilitycan be controlled from AD1640 or AD1680 Series R

Monitor ArmingAlarm contacts are armed for a monitor using a MonitorArming Code which identifies the alarm Display method(Sequence, Hold, or Dual) and

4-1Menu ProgrammingThis section of the manual describes the AD2150 system menuprogramming capabilities.Main Selection Menu...

MENU PROGRAMMING MENU PROGRAMMING All AD2150 programming functions are accessed through on-screen menus. All menus are displayed via the video output

Cursor Positioning and Menu PagingThe following instructions regarding the operation of thecursor apply to all menus.To position the cursor to a desir

The installation of this product should be made by qualifiedservice personnel and should conform to all local codes.QA301F!WWWWAAAARRRRNNNNIIIINNNNGGG

SET TIME AND DATEUse the SET TIME AND DATE menu, below, to set the dateformat, date, time, and day of the week for on-screen displays.DATE FORMAT - T

SET SYSTEM TOURSSet System Tours permits programming of 24 System Tours.A System Tour is a programmed sequence of camera(s) whichhas assigned dwell t

Programming a System TourTo select a tour for programming:1. Move the cursor to TOUR entry in the title line of the SETSYSTEM TOURS menu (page 4-5).2.

SET SYSTEM SALVOSA System Salvo is a group of cameras, with associated presetand auxiliary actions, that can be called simultaneously to acontiguous g

PROGRAMMING A SALVOTo select a System Salvo for programming:1. Position cursor to the SALVO number line in the SETSYSTEM SALVOS menu. 2. Enter the des

SET EVENT TIMERSAn Event Timer permits automatic callup of System Tours toany monitor(s), based on the time of day and the day of week.Each of these a

SET ALARM CONTACTSThis menu allows programming of the alarm contacts input tothe AD2150. 128 entries are allowed (this corresponds to twomodel AD2091

Programming the Alarm ContactsTo select an Alarm Contact for programming:- Move the cursor to the desired Alarm Contact Number(ACN) line of the menu (

MONITOR STATUSSelecting the MONITOR STATUS entry from the Systemmenu provides a status display to the operator. Information regarding each monitor (M

MENU PROGRAMMING - MONITOR MENUMONITORThe Monitor menu configures each monitor. Enter the desiredmonitor number via the keyboard and press the ACK bu

CAMERAThe CAMERA menu is used to create or change the titleinformation for each camera (1-32). This menu is selectedfrom the Main Menu, page 4-3.To s

PORTThe Port menu is used to configure baud rates, data bits, parity,stop bits, and port use for each of the three RS-232 ports. Note: Once the conn

PORT USE TypesTERMINAL - Used to upload and download setup information for the AD2150 from a PC. Select this use type when using theAD2150SW12B soft

ACCESSThe Access menus define the system partitioning, whichcontrols operator keyboard access to monitors, cameras,pan/tilts, and alarms. The system

KEYBOARD/CAMERA VIEWThis Access control function prevents selected keyboards frommanually calling up selected cameras for viewing on anymonitor.Note:

KEYBOARD/CAMERA CONTROL This Access control function prevents selected keyboards fromcontrolling remote functions on selected cameras. (Anycamera tha

MONITOR/CAMERA ACCESSThis Access function defines the Monitor to Camera accesswhich prevents selected monitors from viewing selectedcameras. The MONI

ARM CONTACTSThis Access menu function defines which monitors are armedfor each alarm contact, based upon the monitor ARM TYPEconfiguration in the Moni

AppendixAlarms ... A-2Programming Overview...

Table of ContentsPage SYSTEM DESCRIPTION... 1FEATURES...

ALARMS - PROGRAMMING OVERVIEWAn ALARM is a signal generated by an external device that isconnected to an AD Matrix Switching System, either directly

ALARMS - MONITOR ARMING CODEThe Monitor Arming Code identifies the alarm DisplayClearance methods for the monitor. The Monitor ArmingCode defines th

ALARMS - MONITOR ARMING CODES - ARM TYPESThe following are the available Monitor Arming Codes for theAD2150. Each is identified by the code number,

ALARMS - ARM TYPES (continued)DUAL(13) DHI/DSI - Two alarm monitors, the first armed/alarmedcontact is displayed on the Hold (DHI) monitor. Allsubseq

ON-SCREEN STATUS LINE DISPLAYSSetup/ProgrammingThe following messages appear in the monitor on-screen StatusLine during certain non-menu programming f

AMERICAN DYNAMICS Keyboard Capabilities2078Keyboard 2078,AModel Number 1678C 1678CE 1678CM 1678CME 1677 1677E 1676B 1676BE 1672 ADTTType System Sys E

AUXILIARY KEY GROUPINGF1 - Special function key1 F1 is used to unlock the current camera.2 F1 is used to lock the current camera.F2 - Special functi

COMPUTER CONTROLThe three AD2150 RS-232 control ports use asynchronous, fullduplex, RS-232C protocol. As shipped, all ports are set foroperation at 1

Typical System ConnectionsAD1676 Operator KeyboardAD1678C System KeyboardAD1678CM System KeyboardAD2078A System KeyboardADTT System KeyboardAD1981 Por

PageNON-MENU PROGRAMMING... 3-1System Reset ...

TYPICAL SYSTEM CONNECTIONS AD1676 KEYBOARD TO AD2150RCDXMITGNDTP80597.5 VOLTS AC1.5 AMP4AD167612345678HP00473-WIRE, 18 AWG, SHIELDED CABLE

NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE SYSTEM KEYBOARD.18 AWG TWISTED,SHIELDED PAIR, BELDEN8760 OR EQUIVALENTTP8059232350-AD1678C0XMITRCDGNDACACG

XMITRCDGNDACACGNDBWSCTSDTRDATANOTE : THESE CONNECTIONS ARE TYPICAL OF ONE SYSTEM KEYBOARD. EACH RS232 PORT IS PROGRAMMABLE.TYPICAL SYSTEM

TYPICAL SYSTEM CONNECTIONSAD2078A TO AD2150AD2150AD2078* Items supplied with AD2078A keyboard**Items supplied with AD2150 systemNOTE: CONNECTI

TYPICAL SYSTEM CONNECTIONS ADTT TOUCH TRACKER KEYBOARD FROM AD2150Transformer24 Vac A24 Vac BGroundExternalInterconnectModule (EIM)5 4 3 21J3J2J1T

TYPICAL SYSTEM CONNECTIONS ADTT TOUCH TRACKER KEYBOARD FROM AD2150Transformer24 Vac A24 Vac BGroundExternalInterconnectModule (EIM)5 4 3 21J3J2J1T

AD1676AD2150 NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE AD1981 PORT EXPANDER .EACH RS232 PORT IS PROGRAMMABLE.ToCPU1234567

TYPICAL SYSTEM CONNECTIONS AD1691 CODE DISTRIBUTOR FROM AD215018 AWG SHIELDED TWISTED PAIR ,BELDEN 8760 OR EQUIVALENTSWB ACACSWBBSWJ1CODE LEDTP80021

TYPICAL SYSTEM CONNECTIONSAD1692A CODE MERGER FROM AD215018 AWG SHIELDED TWISTED PAIR ,BELDEN 8760 OR EQUIVALENTBSWTP800212 VOLTS ACRECEIVERAD2150MONI

A A A A A A 1 2 3 4 5 6AD2096ABCDEFGHONOFFONOFFSELECTALARMPWRCOMIN OUTABCDEFGHA A A A A

SYSTEM DESCRIPTIONThe AD2150 System is an integrated Video Matrix Switchingand Control System for CCTV surveillance systems. TheAD2150 is capable of

TYPICAL SYSTEM CONNECTIONSAD2150 TO AD1641 RECEIVERSAD2150BS WB W S B W S B W S B W SCONTROL CODE FROM AD2150 TO RECEIVERSVIDEO FROMCAMERA TOAD2150AD

Declaration of ConformityManufacturer:Sensormatic CCTV Systems DivisionManufacturer’s Address:Sensormatic CCTV Systems Division Sensormatic CCTV Syste

An American Dynamics ProductDesigned and built bySensormatic CCTV Systems DivisionOne Blue Hill PlazaPearl River, New York, 10965(914) 624-7600Technic

Input Identification: The AD2150 provides on-screenidentification of all video inputs. The date, time, cameranumber, camera and monitor status, and a

1-1System InstallationThis section of the manual describes the system installation, connection,and powering up procedures for the AD2150 System.Instal